original part
List of products
The collapsible stock for Sa 58 weapons is new, fully functional, solid at the joint. The joint itself may have minor paint scratches in places due to storage.The stock is in...
Original leaf spring for fire selector Sa58 with both arms.
Comes w/o the spring and pin. Bolt catch holds the bolt opened after the magazine is emptied (or when pressed manually, of course).
Original VZ 58 breech lock. The breech lock performs a swinging movement, during which it locks the entire bolt. It is carried by the bolt carrier together with the bolt....
Original VZ 58 disconnector. A part found in all types of Sa vz.58 clones, except the VZ 2058 weapons, which are equipped with a modified disconnector (you can find it in the...
Original VZ 58 ejector. The ejector ejects empty cartridges back due to the movement of the bolt. By adjusting it, you can achieve a change in the direction of throwing...
Original VZ 58 extractor in caliber 7.62. The component is different for different calibers. The puller is part of the complete bolt, such a small nothing for a lot of money....
Original VZ 58 extractor support. The extractor support is part of the complete bolt and is the same for both calibers. On the side of the smaller diameter, the spring of the...
Original VZ 58 firing pin 7.62. The firing pin is part of the bolt, different for calibers 5.56 and 7.62. For the firing pin, its length is important. If you have a problem...
Original front plate in gray color for original fixed stock.
If you're about to change from folding stock to fixed, you're gonna need this screw to attach it. Length 82mm. Screw is hollowed. Black finish.
This screw is used to attach folding stock to the receiver. Only works with the original folding stock or with D-Force Aggressor stock.
Front sight base for all kinds of the VZ58. New part for gunsmiths. All front sight bases possess the bayonet lug (as shown in the photo). The front sight base is Czech Small...
Original pin for installing the front sight base on the barrel. 2 pins must be used to install the front sight base.
Original VZ 58 gas adapter The device is pressed onto the barrel in the place of the gas channel. It is supplied without a drilled hole for gas collection, without holes for a...
Gas adapter is used for shooting blank ammo. Mounts to the original muzzle threading. Designed to tear up when accidentaly used with live ammo and thus save the rifle (and...
Lower handguard spacer fitting - sits on the end of original lower handguard and reinforces the notch for handguard pin.
Original VZ 58 left and right striker catch with release lever.
Original VZ 58 left striker catch. The left striker catch for VZ.58 is part of the striker catch assembly.
This fitting is placed on the front end of original lower handguard, fits into the gas block. This piece is without the exterior treatment.
Handguard pin secures the lower handguard to the receiver. You have a choice of either the original closed pin (used) or the open type which is newly manufactured.The opening...
This original part can be replaced by a new innovative one, made for faster and easier mag changes. Check our unique parts offer.
One of two original variants of magazine catch pin, goes through a hole in magazine catch and also secures the bolt catch in the receiver. Picture shows variant 2. Variant 1...
This little thing has to be pulled out before you can pull out the magazine catch pin. Made of steel - hardened, blackened
Protects the vulnerable muzzle threading. Has to be screwed all the way down, so it won't protrude over the muzzle edge (which would affect the ballistics). No need to use it...
Original VZ 58 locking pin of the muzzle thread protector. It is installed in the front sight base, where it is locked with the help of a spring and a pin of the base of the...
Original used bayonet for VZ.58. Scales are made of wood-mass filled plastic, blade length 17,5cm, overall length 28,5cm.
Original sling for SA 58 in green color.These are used slings from military weapons.(the picture is only illustrative - the nylon on the slings looks good, only the leather...
Original rare wooden kit from 1958-61 production. This set is without metal parts.We recommend to buy a set of metal parts for the original stock here.
Original pistol grip screw. Also fits Arsenal grips. FAB grips come with a different screw.
Brand new original VZ 58 piston Piston for barrel lengths 300/390/410/473/486. Made of stainless steel with more chrome, very durable and hard material. The piston is...
A vital part to keep the rifle's automatic system working. Length 44mm. Made of spring steel. Original part.
Original VZ 58 piston stopper. The stopper is designed for gunsmiths. It is inserted into the bolt housing before the barrel is pressed and serves as a piston stop in...
Original VZ 58 reciever cover pin The reciever cover pin is used to fix the reciever cover to the gun case. I can't imagine how anyone could screw this up. It is of course...
VZ 58, VZ 58 PARTS, RECEIVER COVER PIN SAFETY PIN, SPARE PARTS
Original VZ 58 reciever cover with springs in very good condition with no surface defects.
Original VZ 58 release lever. The release lever lowers the right firing pin catch when the slide is in the forward position. In a third of its length, it has a hole through...